Contact Us For Quotation | Email: 464560351@qq.com | Whatsapp&Wechat:+8618620373879 |
INTRODUCTION
ETCR9330B Large Caliber Wireless H/L Voltage Clamp Current Meter break through the traditional structure, specially designed and manufactured for measuring high voltage current, the unique U-type opening mouth structure realizes the unimpeded measurement, and very convenient for field test. The meter is composed of special large-caliber U-type current meter with high voltage insulation rod, equipped with wireless receiver, which can receive the measured data within 100 meters straight line distance. ETCR9330B Large Caliber Wireless H/L Voltage Clamp Current Meter used for current measurement of high voltage line below 500kV (connect insulation rod to use), current range: AC 0.00A-9999A, it can directly to test with U-type crrent meter without the insulation rod below 600V. The meter has data hold and data storage and other functions. Insulation rod is equipped with adjustable interface, U-type clamp the tested wire by insulation rod is very convenient, save time and faster. It also can replace the H/L voltage transformation ratio tester, which can measure the H/L voltage current of the primary circuit and the secondary circuit respectively, and then calculate the H/L voltage transformation ratio. The insulation rod is handiness, and has the characteristics of moisture-proof, high temperature resistance, impact resistance, bending resistance, high insulation, scalable and so on. |
SPECIFICATION
Function | Description |
CT Size | Ф128mm |
Sampling Rate | 2 time/second |
Measurement Range | 0.00mA~9999A(50/60Hz automatic) |
Resolution | 0.01A |
Shift | 0.00A~9999A automatic shift |
Test Accuracy | ±2%±5dgt (The wire is near the center of the topof the hooktype clamp,23℃±2℃) |
Position Error | The measured conductor should be located as close as possible to the center of the top of the hooktype clamp. it can hung on the line directly for measurement.Test errors increase one more times or more when away from the top of the hook clamp |
Data Storage | 99 groups, in storage process “MEM” symbol display, “FULL” symbol flash display indicate storage is full |
Line Voltage | Below 110kV current test , operate with insulation rods ( below 500kV can be customized ) |
Data Hold | In general test mode, press HOLD key to hold data, “HOLD” symbol display. press HOLD Key once again to cancel this function |
Data Access | “MR” symbol display, it can look over all the stored data |
Overflow Display | Exceed measurement range overflow function: “OL A” symbol display |
No Signal Indication | When the receiver has not received transmit signal, dynamic display “no- -”symbol. |
Automatic Shutdown | 15 minutes after boot up, the meter shuts down automatically without any operation, to reduce battery consumption |
Battery Voltage | When battery voltage is lower than 4.8V, low battery voltage symbol will display and remind to replace battery. |
Weight | Detector:300g(with Battery ), Receiver:280g(with Battery ), Total weight: : 2300g (include insulation rod and battery) |
Working Environment | -10℃~40℃; Below 80%rh |
Store Environment | -10℃~60℃; Below 70%rh |
External Interference | Should avoid extremely strong electromagnetic fields, avoid 315MHz, 433MHz same-frequency signal interference |
Insulation Strength | AC 220kV/rms(The telescopic insulation rod is fully opened between the two ends) |
Structure | Anti-Dripping Type II |
Selection Guide
Model | Description | Range | Resolution | CT Size | Insulation Rod length | Note |
ETCR9310B | Large Caliber Wireless H/L Voltage U-Type Current Meter | AC0.00A~9999A | 0.01mA | Ф48mm | 5m | wireless transmission |
ETCR9330B | Large Caliber Wireless H//L Voltage Hook Type Current Meter | AC0.00A~9999A | 0.01mA | Ф128mm | 5m | wireless transmission |
Packing Details
Detector | 1 PCS |
Receiver | 1 PCS |
Wireless Antenna | 1 PCS |
Stretch Insulation Rod(4.5m) | 1 PCS |
Meter Case | 1 PCS |
Manual/Warranty Card/Certificate | 1 SET |